2018 Dodge Durango 5.7L Air Intake Installation

Posted on


2018 Dodge Durango 5.7L Air Intake Installation

2018 Dodge Durango 5.7L Air Intake Installation – Hi Dodge readers mania welcome to my weblog. It was an essential pleasure to be as shortly as further contained all through the interim to share particulars referring to the most recent dodge automotive evaluation. On this event, I can also be reviewing the Best dodge engine strongest engine ever constructed .Hopefully, this textual content material materials supplies provides offers provides presents can present further data to you. Well, for an excessive amount of who must get updates regarding the latest dodge auto automotive and observe the occasion of our weblog internet net net web web web net web page for an excessive amount of who happen to wish to know further ,please come as shortly as additional go to as shortly as further with our weblog dodgereviewsrelease.com

2018 Dodge Durango 5.7L Air Intake Installation

This K&N air intake system is designed toincrease power and acceleration by reducing restriction in the intake path K&N’s 63-1563air intake fits 2011 Dodge Durango and 2011 Jeep Grand Cherokee models with 5 7 literengines It comes with K&N’s famous million mile limited warranty The 63-1563 air intakeis not legal for highway use in California or other states adopting

California emissionstandards Check KNFilters Com for an up to date list of models this air intake fits andfor a list of other CARB adoption states K&N power testing showed an estimated powergain of 17 horsepower at 4944 RPM with the 63-1563 air intake installed on a 2011 JeepGrand Cherokee with a 5 7 liter engine Actual results will vary depending on the conditionof the vehicle, mileage, weather and other variables With the air intake installed we ran the vehicleon the dyno to test the sound comparison verses the stock intake

2018 Dodge Durango 5.7L Air Intake Installation

2018 Dodge Durango 5.7L Air Intake Installation

The intake system includes components that have been designed or matched to the needsof these vehicles to produce a safe horsepower increase Detailed installation instructionsare included with this kit The tools needed for this install are shown Turn off the ignition and disconnect the negativebattery cable Lift up the engine cover to dislodge it fromthe mounting grommets then remove it from the vehicle

Remove the intake plenum mounting bolt andloosen the intake tube hose clamp Disconnect the inlet air temperature air sensorelectrical connection Disconnect the crankcase vent hose from thevalve cover port Release the two upper airbox retaining clips Remove the upper airbox and intake tube assembly Unhook the sealing trim from the fresh airintake scoop Lift up the lower airbox to dislodge it fromthe mounting grommets and then remove the lower airbox from the vehicle Install the filter adapter into the heat shieldand secure it with the provided hardware

Remove two of the factory airbox mountinggrommets from the lower airbox Install the two mounting grommets removedin the previous step into the heat shield Install the provided edge trim onto the heatshield Install the provided silicone hump hose ontothe filter adapter and secure it with the provided hose clamp Set the heat shield into the vehicle so thatthe mounting grommets slide over the factory airbox mounting studs Install the K&N air filter onto the adapterand secure it with the provided hose.

2018 Dodge Durango 5.7L Air Intake Installation

2018 Dodge Durango 5.7L Air Intake Installation

clamp Install the provided silicone hose onto thethrottle body and secure it with the provided hose clamp Release the locking tab then remove the inletair temperature sensor from the factory intake tube by twisting it counter clockwise Install the provided grommet into the K&Nintake tube Install the inlet air temperature sensor intothe K&N intake tube Install the 90 degree npt fitting into theK&N intake tube Install the K&N intake tube into the siliconehump hose then into the silicone hose at the throttle

2018 Dodge Durango 5.7L Air Intake Installation

body Secure the intake tube withthe provided hose clamp Install the crankcase vent hose onto the 90degree vent fitting then attach the open end to the valve cover port Connect the inlet air temperature sensor extensionharness into the factory electrical connection then connect the other end into the inletair temperature sensor Reinstall the engine cover Reconnect the vehicle’s negative batterycable Double check to make sure everything is tight and properly positioned before startingthe vehicle It will be necessary for all K&N high flowintake systems to be checked periodically for realignment, clearance and tighteningof all connections Failure to follow the above instructions or proper maintenance mayvoid warranty K&N makes products for nearly every vehicleon the road The K&N website allows you to search products by vehicle or dimension, downloadinstallation instructions, view dyno charts showing estimated horsepower gains for thisproduct, and view product details For information on where to buy K&N products, go to knfilters.

2018 Dodge Durango 5.7L Air Intake Installation